Information for correct use
PRECAUTIONS TO THE ASSEMBLY OF CYLINDER
Avoid applying loads on the stem that are coaxial, this to avoid lateral forces in the long run could affect the proper functioning of the internal organs: the actuator is a component which would win only and exclusively axial forces (along the axis of the screw ).
PRECAUTIONS TO THE ASSEMBLY OF THE ENGINE
If you have purchased one of our electric cylinder version CUSTOM means that the engine flange were machined specifically for the assembly of your engine.
If the cylinder is equipped to mount the motor returned, you must remove the rear pulley cover, coves hand without blocking the pulley on the shaft, "fit" the belt on the pulley and put the engine cover in place.
Block with screws and rotating the engine by hand to verify that the two belt pulleys are aligned and then lock the pulleys on their respective trees.
If the cylinder is designed for direct mounting of the engine, there is a connection joints with locking clamp. To avoid twisting the shaft, you first plug the motor into place, then the coupling block well on both trees (screw and motor) and only finally tighten the screws of the motor, after verifying that it is centered into place.
PRECAUTIONS SHOCK
In the event of a collision by the internal movement against the heads (front and back) and some breakage of the bearing. For this reason, since we installed new bearings and controlled, are excluded from the guarantee. And 'necessary before use to ensure the installation of control devices limit switches.
PRECAUTIONS IN VERTICAL APPLICATIONS
The ball screws are "always" reversible, to secure the load with the engine off, it should use the brake on the engine.
SELECTION AND USE PRECAUTIONS ENGINE
Attention to the peak torque of brushless motor, can usually also be 5 times the rated torque. The cylinder power with all the safety factors that guarantee an unlimited use, is planned for a maximum torque input specifically designed for each model.
The possible "peak" torque unchecked can permanently damage the cylinder.
TRANSMISSION BELT TOOTHED
If you purchased one of our electric cylinder engine delayed the transmission of motion between screw shaft and is secured by a toothed belt snugly reinforced with Kevlar to prevent the stretch. The belt tension is "predetermined" are therefore not required nor any subsequent interventions turnbuckles for tensioning the timing belt.
The locking of the pulleys on the respective shafts (motor and screw) may be made by clamping or locking grains depending on the size of the cylinder and the engine.
BACK to FAQ
Avoid applying loads on the stem that are coaxial, this to avoid lateral forces in the long run could affect the proper functioning of the internal organs: the actuator is a component which would win only and exclusively axial forces (along the axis of the screw ).
PRECAUTIONS TO THE ASSEMBLY OF THE ENGINE
If you have purchased one of our electric cylinder version CUSTOM means that the engine flange were machined specifically for the assembly of your engine.
If the cylinder is equipped to mount the motor returned, you must remove the rear pulley cover, coves hand without blocking the pulley on the shaft, "fit" the belt on the pulley and put the engine cover in place.
Block with screws and rotating the engine by hand to verify that the two belt pulleys are aligned and then lock the pulleys on their respective trees.
If the cylinder is designed for direct mounting of the engine, there is a connection joints with locking clamp. To avoid twisting the shaft, you first plug the motor into place, then the coupling block well on both trees (screw and motor) and only finally tighten the screws of the motor, after verifying that it is centered into place.
PRECAUTIONS SHOCK
In the event of a collision by the internal movement against the heads (front and back) and some breakage of the bearing. For this reason, since we installed new bearings and controlled, are excluded from the guarantee. And 'necessary before use to ensure the installation of control devices limit switches.
PRECAUTIONS IN VERTICAL APPLICATIONS
The ball screws are "always" reversible, to secure the load with the engine off, it should use the brake on the engine.
SELECTION AND USE PRECAUTIONS ENGINE
Attention to the peak torque of brushless motor, can usually also be 5 times the rated torque. The cylinder power with all the safety factors that guarantee an unlimited use, is planned for a maximum torque input specifically designed for each model.
The possible "peak" torque unchecked can permanently damage the cylinder.
TRANSMISSION BELT TOOTHED
If you purchased one of our electric cylinder engine delayed the transmission of motion between screw shaft and is secured by a toothed belt snugly reinforced with Kevlar to prevent the stretch. The belt tension is "predetermined" are therefore not required nor any subsequent interventions turnbuckles for tensioning the timing belt.
The locking of the pulleys on the respective shafts (motor and screw) may be made by clamping or locking grains depending on the size of the cylinder and the engine.
BACK to FAQ